How to Replace a Bath Tub
How to Replace a Bath Tub
Blog Article
Listed here down the page you might get more superb additional info with regards to Installing A Bathtub.
Setting up a bathtub isn't specifically rocket science, yet it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately difficult job. If the old tub is easily accessible, the job can relocate rapidly; if you have to open up a wall to get rid of the old tub and also position the brand-new bath tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will need a helper to vacate the old tub as well as embeded in the new one. See to it you have qualified on your own for the job and also are comfortable attempting it. As opposed to hiring a specialist to take over a halfway-completed job, it is far better to take into consideration employing one before you start. Chances are you may require a professional plumber to make tube connections.
This write-up will assist you mount a new bathtub in your shower room if you have actually already purchased a brand-new bathtub and also don't need to alter the setup of your previous water supply pipes.
Your devices and also material checklist must consist of the following:
Planning for the Installment
First of all, the sustaining structure provided with the bath ought to be fitted (if needed) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be rather troublesome due to the limited accessibility that is usually the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will originate from the pipelines. When the supply pipes have been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Before going on to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bathtub
Making use of the two wooden boards under its feet, position the tub in the required placement. The wooden boards are handy in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the bath tub up until the level checks out degree.
To install faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water as well as examine all joints and brand-new pipework for leaks as well as tighten them if essential. Fill up the bath tub and likewise check the overflow outlet and also the normal electrical outlet for leakages.
Lastly, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and also securing around the bathtub ought to wait till the bathtub has actually been made use of a minimum of when as this will settle it right into its last position.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washers are in location in between the faucet and the sink. Secure the tap in position with the supplier given backnut. When the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former type must be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to split a stiff seal, triggering the water to pass through the wall surface in between the bath and the tiling, leading to difficulties with wetness as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes and also cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealant can fracture rather early if you do not take into account this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that write up on Installing A Bathtub while scouting around the internet. In case you appreciated our blog posting please do not forget to pass it around. I enjoy reading our article about Installing A Bathtub.
Source Report this page